Sequence for 13.2Ah SmartCore Lupine battery:
1- With the battery
not connected, press and hold button until 100% LED only comes on (it takes about 8 seconds), then let go. PRESS the button 1 time while the 100% LED is still shining.
2- Wait... until 80% LED comes on, then press button three (3) times.
3- Wait... as it cycles through some other LEDs; but do not press the button anymore.
4- Wait... the array will flash, and you're done with the technical stuff!
5- Now, you must
discharge the battery (with a lamphead), and finally,
fully recharge. This should solve the problem.
Sequence for 11.2Ah SmartCore Lupine battery:
1- With the battery
not connected, press and hold button until 100% LED only comes on (it takes about 8 seconds), then let go. PRESS the button 1 time while the 100% LED is still shining.
2- Wait... until 80% LED comes on, then press button one (1) time.
3- Wait... as it cycles through some other LEDs; but do not press the button anymore.
4- Wait... the array will flash, and you're done with the technical stuff!
5- Now, you must
discharge the battery (with a lamphead), and finally,
fully recharge. This should solve the problem.
Sequence for 8.4Ah SmartCore Lupine battery:
1- With the battery
not connected, press and hold button until 100% LED only comes on (it takes about 8 seconds), then let go. DO NOT PRESS the button as long the 100% LED is still turned on - wait until it turns off.
2- Wait... until 80% LED comes on, then press button eight (8) times.
3- Wait... until 40% LED comes on, then press button two (2) times.
4- Wait... the array will flash, and you're done with the technical stuff!
5- Now, you must
discharge the battery (with a lamphead), and
finally, fully recharge. This should solve the problem.
Sequence for 6.6Ah SmartCore Lupine battery:
1- With the battery not connected, press and hold button until 100% LED only comes on (it takes about 8 seconds), then let go. DO NOT PRESS the button as long the 100% LED is still turned on - wait until it turns off.
2- Wait... until 80% LED comes on, then press button six (6) times.
3- Wait... until 60% LED comes on, then press button four (4) more times.
4- Wait... the array will flash, and you're done with the technical stuff!
5- Now, you must discharge the battery (with a lamphead), and finally, fully recharge. This should solve the problem.
Sequence for 5.6Ah SmartCore Lupine battery:
1- With the
battery not connected, press and hold button until 100% LED only comes on (it takes about 8 seconds), then let go. DO NOT PRESS the button as long the 100% LED is still turned on - wait until it turns off.
2- Wait... until 80% LED comes on, then press button five (5) times.
3- Wait... until 60% LED comes on, then press button five (5) more times.
4- Wait... the array will flash, and you're done with the technical stuff!
5- Now, you must
discharge the battery (with a lamphead), and
finally, fully recharge. This should solve the problem.
Sequence for 2.7Ah SmartCore Lupine battery:
1- With the
battery not connected, press and hold button until 100% LED only comes on (it takes about 8 seconds), then let go. DO NOT PRESS the button as long the 100% LED is still turned on - wait until it turns off.
2- Wait... until 80% LED comes on, then press button twice (2 times).
3- Wait... until 60% LED comes on, then press button five (5) times.
4- Wait... the array will flash, and you're done with the technical stuff!
5-Now, you must
discharge the battery (with a lamphead), and
finally, fully recharge. This should solve the problem.
Sequence for 1.7Ah SmartCore Lupine battery:
1- With the
battery not connected, press and hold button until 100% LED only comes on (it takes about 8 seconds), then let go. DO NOT PRESS the button as long the 100% LED is still turned on - wait until it turns off.
2- Wait... until 80% LED comes on, then press button once (1 time).
3- Wait... until 60% LED comes on, then press button five (5) times.
4- Wait... the array will flash, and you're done with the technical stuff!
5- Now, you must
discharge the battery (with a lamphead), and
finally, fully recharge. This should solve the problem.